top of page
LokBuild logo
header_lokbuild.jpg

3D PRINT BUILD SURFACE

 
The ultimate printing surface for 3D printers. LokBuild provides a durable and stable build surface whilst preventing model warping.
lokbuild_office1.jpg

LOKBUILD
FEATURES

  • Optimal 3D Printing Surface

  • Improves Model Adhesion

  • Reduces Warping

  • Easier Nozzle Height Calibration

  • Durable and Long Lasting

  • Protect your Build Plate

  • Easy Removal of Completed Prints

  • One Build Surface for most materials

  • Easy to Install

THE SOLUTION

 

Are you having difficulties getting your 3D prints to stick without warping? Struggling to remove your finished model after printing? Tired of messing around with inadequate solutions such as kapton, blue builders tape, hairspray and ABS slurry? LokBuild is the answer!

LokBuild provides the perfect printing surface for 3D models to adhere and also allows completed objects to be removed easily. LokBuild is a durable sheet that sticks to the bed of 3D printers.

WHAT IS LOKBUILD?

 

LokBuild is the ultimate 3D printing surface for FFF/FDM 3D printers. It is a long lasting alternative to films and tapes.

LokBuild can be easily cut to suit the exact shape and size of your 3D printers build surface. LokBuild is made from uniquely textured sheets that attach to your build plate easily with heat-resistant adhesive backing.

LokBuild replaces the need for blue masking tape or polyimide films such as Kapton Tape. It is made from heat-resistant materials to provide a stable build platform for 3D printed models whilst allowing completed models to be removed easily.

LOKBUILD MATERIALS

We are constantly testing new materials. Here is a list of just some materials that have been successfully printed on LokBuild...

ABS, PLA, HIPS, PET

 

colorFabb_XT, colorFabb nGen, colorFabb_HT, colorFabb XT-CF20 (carbon fibre)

 

Woodfill, Bronzefill, Copperfill, Brassfill

Polymaker PC-Plus (polycarbonate), Polymaker PC-Max (polycarbonate), Polymaker PolyFlex, Ninjaflex

lokbuild_bg4.jpg

IMPROVED MODEL ADHESION
AND REDUCED WARPING

HOW TO USE LOKBUILD

If you have ever used tape or films you will know that they are difficult to fit. LokBuild is more rigid and really easy to apply to your build plate. Also it is almost impossible for air bubbles to get trapped beneath the LokBuild surface.

INSTALLATION

1) Wipe down the build platform making sure it is clean.

2) Trim LokBuild to match the shape and size of your build plate. This can be done easily with general household scissors or a craft knife.

3) Remove the adhesive backing and apply LokBuild to the build plate. Start from one side and work your way to the other side, smoothing LokBuild as you go.

4) Adjust the printers nozzle height and check that the build surface is level.

HOW TO CLEAN LOKBUILD

LokBuild should not need to be cleaned very often but if you do please use alcohol wipes or similar (low % Isopropyl). Do not use acetone or anything with a high % Isopropyl, this will damage the surface.

NOZZLE HEIGHT CALIBRATION

LokBuild is much more forgiving than some other products when setting the nozzle height and does not require such a high level of accuracy. However there will be an optimal nozzle height for your chosen material and printer.

 

The key to a good nozzle height is to experiment. We recommmend starting further away from the bed than with other surfaces and then reduce the nozzle height slightly until the print sticks to LokBuild.

 

The vast number of printers and materials makes it impossible to give exact print parameters but a good starting point for the nozzle height would be between 0.20mm - 0.25mm.

 

TIP: When setting the nozzle height start further away from the bed than with other surfaces such as tapes. LokBuild works better without squashing the filament too much on the first layer.

REMOVING COMPLETED PRINTS

In most cases prints will pop off cleanly with minimal effort. However on some models with larger contact areas a spatula may be useful.

 

TIP: When printing with the bed heated above 100 deg C it is good practice to allow the build surface to cool before removing the prints. This will increase the lifespan of your LokBuild surface.

TROUBLESHOOTING

lokbuild_bg3.jpg

WHY CHOOSE LOKBUILD?

The Ultimate 3D Print Build Surface...
lokbuild_bg1.jpg

DURABLE AND LONG LASTING
PROTECT YOUR BUILD PLATE

bottom of page